Cheap Shopping Tips UK

This Whirlpool washer troubleshooting guide can come handy when you experience problems with your Whirlpool top load or front load washing machine. Whirlpool is actually the biggest appliance company today. They have been producing some of the most reliable washers and household appliances for the longest time. They have also acquired the rights to other appliance companies such as Maytag.
Despite the obvious excellence and the cutting edge technology incorporated of Whirlpool washers, they are still not exempt from problems. Washers are prone to breakage. Because of daily wear and use of water, energy and detergent, the parts wear out quickly.
Every Whirlpool washer owner must know how to diagnose their Whirlpool washer troubleshooting problem and learn how to do first aid treatments to it. This will prolong the life of the washer without actually spending a lot of money on repairs.
How To Diagnose The Whirlpool Washer Problem
More often than not, the problem is centered on the machine’s motor system. You can begin checking on this area of your washer. But first you have to know how to get to the motor area. If you have the original user manual of the washer, try to refer to that to get more information about the specific parts of the washer. This will help you determine the parts that are more likely to break down.
You will need a screwdriver and a small bin to place the screws you removed from the washer. You might also need some towels to absorb excess moisture. Here are a few steps on how to diagnose washer problem:
Step 1: Turn your washer off first and unplug it. Let the machine rest for about 15 minutes after unplugging to remove any lingering current.
Step 2: Use the absorbent towel to carefully remove any lingering moisture around or inside the washing machine. You might also want to don a glove to protect your hands.
Step 3: Check the bottom part of the washer for any signs of black dust. If there are any, the problem could be in the motor coupling. Bad motor coupling usually triggers improper spinning or agitation of the washer.
Step 4: Check the lid switch of the washer and find out if there are signs of wear and tear. You can also use a voltmeter to test the lid switch. This can also be the reason for the failure of the washer in spinning.
Step 5: Check the pump of the washer. This usually has a gray plastic cover with two black colored hoses attached to it. If there are any punctures of bubbles on the pump, this might cause a leaky problem.
Step 6: Also check the pump for clogging. A sock can get easily lodged in there which will then cause washer drain problems. Remove the pump using a clamp and then check for clogs inside.
Whirlpool Washer Troubleshooting Guide – Fix A Washer That Won’t Spin
A failure to spin problem centres mostly on the washer drive belt. You have to replace the drive belt. Open the cabinet of the washer or the back panel, depending on the design of your washer. Remove the mounting screws of the motor and loosen up the belt. Remove it and replace it with a new one or tighten it.
Also check the lid switch. Buy a replacement switch if the old switch is not clicking in place.
Whirlpool Washer Troubleshooting Guide – Fix A Leaky Washer
Your washer might leak due to two causes: punctured pump or loose water hose. If the leak is coming from outside the washer, check the water hose first. Turn off the water source and remove the hose. Check the rubber seal of the hose for signs of deterioration. You might need to replace the old hose if it is no longer working properly.
If the hose is not the problem, it could be the pump. After opening the washer or removing the back panel, check the gray plastic piece called the pump for signs of punctures or leaks. If there are any, have it replaced immediately or try to seal the puncture using a store-bought sealant.
Whirlpool Washer Troubleshooting Guide – Fix A Clogged Washer
If it is slow to drain, check the drain pipe for accumulated debris. Run an empty water cycle and add a cup of white vinegar. This will help loosen up the debris. If this trick did not work, the pump might be clogged with a sock or another piece of clothing. Try to remove the pump and remove the clothing that has been clogging the washer.

Read more about Whirlpool Washer Troubleshooting Guide – Fix Your Washer Pronto!